Grade and Finish to List on a Stainless Duct Request

Most duct on a commercial job is galvanized, and most quote requests are written with galvanized in mind. When a spec section calls for stainless steel on part of the system, the request needs a few more notes. Stainless is priced and built differently, and a line that just says "SS" leaves the shop guessing about the things that matter most: which grade, how thick, and what the surface has to look like.

This article covers what to list on a stainless duct request so it can be priced without a call-back: the grade, the thickness, the finish, the seams and connections, and where on the drawings the stainless runs start and stop.

For the full quote checklist (drawings, materials, connections, releases, pickup or delivery), see the Contractor Guide. For stainless duct as a product, see Stainless Steel Duct. This post covers rectangular-style stainless duct and fittings only, and stays on the request notes.

DuctAxis is a commercial duct fabricator in Clewiston, Florida. We fabricate stainless steel duct and drain pans when a project calls for them. We do not install.

Why stainless requests get sent back

On a galvanized job, a lot of detail can be filled in from the rest of the set. Stainless is usually a smaller, specific part of the job, and the details live in one spec section that may not travel with the drawings. When that section is missing, the shop cannot tell what was intended.

Common gaps on stainless requests:

  • "Stainless" or "SS" with no grade
  • No thickness, or a thickness written for galvanized and carried over
  • No finish called out, or a finish named only as "polished" or "clean"
  • No note on how seams and joints are to be made
  • No clear limits on the drawings showing which runs are stainless and which are not

A request with the notes below is enough to start estimating.

Start with the spec section

Before anything else, send the spec section that calls for stainless. That is the document that decides the grade, thickness, finish, and joining method. If the job has more than one duct spec section, say which one applies to the stainless runs.

If a note on the drawings and the spec disagree, flag it in the request rather than picking one. "Drawing note says stainless, spec section lists galvanized for this system, please price as stainless and confirm" is a useful line. It is better to raise the conflict up front than to find it after the quote.

List the grade exactly as written

Stainless comes in more than one grade, and the grade affects both price and how the piece is built. Write the grade exactly as the spec states it, including any letter suffix. Do not shorten it, round it to a more common grade, or leave it to the shop to choose.

  • One grade for the whole scope: write it once at the top of the request.
  • More than one grade: list which runs or fittings use which grade, by mark, system, or drawing sheet.
  • No grade on the documents: say so. Write "grade not specified, to be confirmed" so the question goes to the engineer of record before the order is released, not after.

List the thickness by run

Write the thickness (gauge or decimal thickness, in the form the spec uses) for each part of the stainless scope. If the spec ties thickness to duct size, send that table or reference the paragraph that has it.

A few things to watch:

  • If the spec gives a different thickness for stainless than for galvanized, use the stainless number. Do not carry a galvanized gauge over to a stainless line.
  • If fittings, access panels, or drain pans have their own thickness, list them separately.
  • If the documents do not give a thickness, leave it open and flag it. It can be confirmed during estimating. Do not guess a number to make the request look complete.

Name the finish and where it shows

Finish is the note most often left off a stainless request, and it changes what the shop has to do to the sheet and how the piece is handled after fabrication.

  1. Finish designation. Write the finish the spec calls for, using its exact wording or designation. "Polished" alone is not enough.
  2. Which faces. Say whether the finish applies to the exposed outside only, the inside, or both.
  3. Exposed or concealed. Note whether the duct will be visible in the finished space or above a ceiling or in a chase. If the spec treats exposed and concealed runs differently, say which is which.
  4. Protection. If the spec calls for a protective film or covering on finished surfaces, note it.

If the documents do not name a finish, write "finish not specified" rather than leaving the line blank. That keeps the question visible.

Note seams, joints, and connections

How stainless is joined is part of the price. Send what the documents state:

  • Longitudinal seams, as the spec calls for them
  • Transverse joints and connections between sections, and at equipment or other materials
  • Sealing or testing requirements, when the spec requires them on the stainless runs
  • Any welding requirements the spec lists, including finish of welds on exposed work

Do not invent a seam type, joint type, or test requirement on the request. If the documents do not say, flag it and it can be confirmed during estimating.

Mark where stainless starts and stops

On a mixed job, the drawings need to show the limits of the stainless scope clearly.

  1. Mark the start and end of each stainless run on the plan, with sheet numbers.
  2. Note the connection where stainless meets galvanized or another material, if the documents show one.
  3. List the stainless fittings by mark, with sizes as width x height for rectangular, in the same order the rest of the set uses.
  4. Include any stainless drain pans or accessories the documents call for, with their marks and sizes.

If the stainless limits are only described in a note ("all duct serving this system to be stainless"), say which system that is and which sheets show it.

Quick checklist before you send the request

If a box is empty, either fill it in or flag it in the request ("finish to be confirmed by engineer before release"). That is faster than a request that looks complete and is not.

How this fits the stainless steel duct page

The Stainless Steel Duct page is where stainless duct work lives: stainless ductwork fabricated for commercial projects that specify stainless construction. That page lists what to send for a quote. This article does not replace it; it only explains how to write those grade, thickness, and finish notes so the request arrives with what the shop needs.

When you are ready to price the package, use the Contractor Guide for project details, drawings, construction requirements, dates, and pickup or delivery notes.

Send your stainless request

When the notes are ready, save the drawings and spec section as legible PDFs and request a quote. Uploads accept PDF, XLSX, XLS, CSV or ZIP files: up to 8 files, 20 MB each, 50 MB total. For a larger package, call (863) 599-7014 or email office@ductaxis.com.

  • Quote response time: under 48 hours, excluding weekends. That is how long it takes to get a quote back, not the fabrication lead time.
  • Shipping: Free shipping anywhere in Florida. Delivery outside Florida is confirmed with your quote.
  • Shop: 535 E El Paso Avenue, Suite C, Clewiston, FL 33440

Free estimates from your mechanical plans (PDF). Send what you have; a clear grade, thickness, and finish note still makes the first pass cleaner.

Final dimensions, materials, and fabrication follow your approved project requirements and are confirmed during estimating. This article is general guidance for writing stainless duct requests and does not replace your project specifications, drawings, or engineer of record.