What to Mark on a Plenum Box Quote Request
A plenum box often shows up on a request as a rectangle on the plan with a tag and an overall size. But a plenum box is mostly about its openings: where they are, how big they are, what connects to each one, and what is inside the box. When those details are not marked, the shop has to ask before it can price the box.
This article covers what to mark on a plenum box request before you send it: the box dimensions, the opening locations measured from a fixed reference edge, the connection types and orientation, clear opening versus outside dimensions, lining or insulation and internal components, and the material and gauge from your project drawings.
For the full quote checklist (drawings, materials, connections, releases, pickup or delivery), see the Contractor Guide. For plenum boxes as a product, see Plenum boxes. This post stays on the request notes.
DuctAxis is a commercial duct fabricator in Clewiston, Florida. We fabricate plenum boxes to the dimensions and requirements you send. We fabricate; you install. Your installation scope and customer relationships remain yours.
Why plenum box requests get sent back
Most of what a plenum box needs is already somewhere in the drawing set. The trouble is that it is often spread between the plan view, a detail, the equipment schedule, and a note on another sheet.
Common gaps on plenum box requests:
- An overall size with no note on whether it is the outside of the box or the clear inside
- Openings shown on the plan but not dimensioned
- Opening locations with no reference edge, so the numbers can be read more than one way
- No connection type listed for each opening
- No note on which way each opening faces
- Lining or insulation mentioned in a general note but not tied to the box
- No material or gauge listed
A request with the notes below is enough to start estimating.
List the box dimensions
Start with the overall box. Give the length, width, and height, and say what each number measures.
- Write all three dimensions. A plan view usually shows two. The third is often in a section, a detail, or a schedule.
- Say which side is which. If the box has a top, bottom, and sides that matter for the openings, label them the same way every time on the request.
- One box per line. If the job has more than one plenum box, list each by mark or tag, in the same order the drawings use.
If the documents do not give a dimension, leave it open and flag it. Do not guess a number to make the request look complete.
Clear opening or outside dimension
This is the note that causes the most back-and-forth. The same box can be described by its outside size or by its clear inside size, and the difference matters once lining or insulation is involved. The same goes for each opening: a number can mean the clear opening or the outside of a collar or connection.
For every dimension you send, say which one it is:
- Box size: outside of the finished assembly, or clear inside
- Opening size: clear opening, or outside of the connection
- Lined boxes: whether the clear dimension is measured inside the lining or inside the metal
If the drawings say "clear" or "outside" next to a number, copy that word onto the request. If they do not say, flag it so it can be confirmed during estimating.
Locate every opening from a fixed reference edge
Opening locations are where most plenum box questions come from.
- Pick one fixed reference edge or corner of the box, name it on the request, and use it for every opening on that face.
- Give each opening size as width x height (or diameter for a round opening).
- Give the offset from the reference edge to the edge of the opening, in both directions, and say whether you are measuring to the edge or the center of the opening.
- Note which face of the box each opening is on, using the same face labels you used for the box dimensions.
- If two openings sit close together or line up with each other, dimension both from the same reference rather than from each other.
A simple marked-up sketch of each face works well. Draw the face, mark the reference edge, and write the offsets and opening sizes on it. Save it as a PDF with the rest of the drawings.
Label connection type and orientation
Each opening connects to something: a duct run, a piece of equipment, a diffuser, or another fitting. The shop needs to know what kind of connection each opening gets and which way it faces.
For each opening, note:
- Connection type, as the drawings or specifications describe it
- Orientation, meaning which way the opening faces and, for a rectangular opening, which dimension is width and which is height
- What it serves, such as the associated equipment tag or duct run, so the opening can be checked against the rest of the set
If the connection type is not shown, write "connection not specified, to be confirmed" so the question gets answered before the order is released, not after.
Lining, insulation, and internal components
Next, say what goes inside the box or on it.
- Lining or insulation. If the drawings or specifications call for lining or insulation, note it exactly as written, including thickness if given, and whether it is inside or outside the box.
- Internal components. If the box has parts inside it, call each one out and note where it sits. Copy the description from the drawings rather than renaming it.
- Access. If the drawings show access for internal components, note it and where it goes.
If a general note says plenums are lined but the box detail does not show it, flag the conflict.
Material and gauge from the project drawings
Write the material and gauge the project drawings or specifications call for. Use the same wording the documents use.
- If different plenum boxes on the job use different materials or gauges, list which is which.
- If no material or gauge is given, write "material and gauge not specified, to be confirmed" so the question goes to the engineer of record before the order is released.
Quick checklist before you send the request
- Each plenum box listed by mark or tag
- Length, width, and height for each box
- Box size marked as outside or clear inside
- Face labels used the same way throughout
- One fixed reference edge named for each face
- Every opening sized as width x height or diameter
- Every opening located from the reference edge, edge or center noted
- Opening sizes marked as clear opening or outside of connection
- Connection type for each opening, or flagged as not specified
- Orientation and the equipment or duct run each opening serves
- Lining or insulation per documents, inside or outside noted
- Internal components called out with locations
- Material and gauge per documents, or flagged as not specified
- Drawings, details, and sketches saved as legible PDFs
If a box is empty, either fill it in or flag it in the request ("opening location to be confirmed before release"). That is faster than a request that looks complete and is not.
How this fits the plenum boxes page
The Plenum boxes page is where plenum box work lives: plenum boxes fabricated to your commercial ductwork and equipment requirements. That page lists what to send for a quote: box dimensions, opening locations, connections, and lining or insulation requirements. This article does not replace it; it only explains how to mark those items on the request so it arrives with what the shop needs.
When you are ready to price the package, use the Contractor Guide for project details, drawings, construction requirements, dates, and pickup or delivery notes.
Send your plenum box request
When the notes are ready, save the drawings, details, and marked-up sketches as legible PDFs and request a quote. Uploads accept PDF, XLSX, XLS, CSV or ZIP files: up to 8 files, 20 MB each, 50 MB total. For a larger package, call (863) 599-7014 or email office@ductaxis.com.
- Quote response time: under 48 hours, excluding weekends. That is how long it takes to get a quote back, not the fabrication lead time.
- Shipping: Free shipping anywhere in Florida. Delivery outside Florida, including LTL freight, is confirmed with your quote.
- Shop: DuctAxis, 535 E El Paso Avenue, Suite C, Clewiston, FL 33440
Free estimates from your mechanical plans (PDF). Send what you have; a named reference edge and clear opening notes still make the first pass cleaner.
Final dimensions, materials, and fabrication follow your approved project requirements and are confirmed during estimating. This article is general guidance for writing plenum box requests and does not replace your project specifications, drawings, or engineer of record.
Request a quote